Titanium General || Upgrading DVR/NVR from V1.2.x to V1.3.x via USB Flash Drive ||

Titanium General || Upgrading DVR/NVR from V1.2.x to V1.3.x via USB Flash Drive ||

Upgrading DVR/NVR from V1.2.x to V1.3.x via USB Flash Drive

Published: October 9, 2026



When to Use This

DVRs and NVRs running V1.2.6 or earlier (V1.2.x, V1.1.0, etc.) cannot upgrade directly to V1.3.3 or later.


This USB procedure brings them to V1.3.x first. After that, normal upgrade paths apply.


Current version

Path

V1.2.6 or earlier

This USB procedure → V1.3.x → then V1.3.3+

V1.3.x

Standard upgrade



⚠️ Read Before You Start

1. The files on the USB drive must be byte-identical to the source. A corrupted copy fails the upgrade. If the serial port log shows "Image bad data checksum", this is almost certainly why — not the device. Corruption comes from a faulty USB drive or a virus on the computer. Verify with Beyond Compare (procedure below).


2. If one device fails, stop. Do not continue to other devices. Find out whether the cause is item 1 and get one device upgraded successfully before touching the rest.


3. Use the USB 2.0 port — the white one.


4. Some USB drives are not recognized. After a few attempts with no result, swap to a different drive rather than troubleshooting the device.



Upgrade Steps

1. Prepare the USB drive

Copy all four files to the root directory of the USB flash drive:


  • appfs_special_hi3536

  • firmware3536

  • N0I_UI1B_133.fls

  • ubt3536m

2. Start the upgrade

  1. Insert the USB drive into the device's USB 2.0 port.

  2. Power off the device.

  3. Wait two minutes.

  4. Power on. The upgrade starts automatically.

3. First stage — about 5 minutes

Screen shows: "System is upgrading in 1-5 minutes, please don't power off"


Then it reports reading parameters, and that the first stage completed — "Parameters OK. Upgrading to v1.3.x"

4. Second stage — about 4-5 minutes

The device continues to V1.3.3 on its own.


  • Do not remove the USB drive.

  • Do not restart the device.


Sequence: upgrade prompt (~2 min) → startup logo (~30 sec) → progress bar (~2 min) → device enters the system.


Upgrade complete. Total time: roughly 10 minutes.



If the Screen Stays Black After Restart

With the USB drive still inserted, in this order:


  1. Unplug and reconnect the video cable.

  2. If still black, reconnect the USB drive.

  3. If still black, try a different USB port.



Verifying the Files with Beyond Compare

Use this when an upgrade fails, or before a batch to rule out a bad drive.


  1. Install and run Beyond Compare.



  1. Click Folder Compare.


  2. Load the source folder in one pane and the USB drive in the other — select them, or drag the folders in.


  3. Select the files, right-click, choose Compare Contents.


  4. In the dialog, select Binary comparison and click Start.


  5. Review the result. Double-click any file to see the differences.


A binary mismatch on any of the four files means the copy is bad. Re-copy, or replace the USB drive.



Field Notes

"Image bad data checksum" is a copy problem, not a device problem. It points at the USB drive or the computer that wrote it. Replacing the drive fixes it more often than anything done to the DVR.


The two-minute wait after power-off matters. It is in the vendor procedure; don't shorten it.


Budget about 10 minutes per device, plus the power-off wait — and verify files once per drive before a batch rather than per device.