Akuvox Local || A092: Device and DoorStrike setup Through Wiegand || Installation

Akuvox Local || A092: Device and DoorStrike setup Through Wiegand || Installation

Akuvox A092 Device and  DoorStrike setup Through Wiegand

If installing a door strike to A092 Controller with a doorbell  that has either a door strike or mag lock and a user does not want to utilize an Action URL, they must then wire the doorbell through Wiegand. With this setup there are two ways to power the strike/lock, first being  external power or utilizing the power that the A092 provides. This setup will use Pin Codes

First wire  Wiegand_A_D0, Wiegand_A_D1, and Ground

This will be wired for both the A092 and whichever device you are using.

 

This example uses an R27

Next you will connect your door strike.

  • If with external power Normally Open and Relay common will be utilized 

I.E: In this example we will utilizing the power from the A092

Because we are utilizing this power we will need a Jumper that allows for the transfer of voltage through the door strike. 




Wiring Goes as Followed  

  • Red: Relay_No
  • Black: Ground
  • Jumper from 12V To Relay_COM

Setup device on Cloud add Manager and open Manager account

ADD a NEW person/resident/family/etc and set up their PIN

. 

 

Example pin: 741852

Once adding their Pin number its best to use 4-6 numbers for this to be an easier conversion from Decimal to Hexadecimal 

Open Calculator on your computer>Left hash marks>Standard to Programmer mode> in DEC add pin>HEX will be your HEX conversion  

NOTE: the HEX form must be added in the RF card section and must contain 8 characters. In our example there were 5 characters generated when adding the pin so we add 3 zeros to the front of the 5 characters to make a total of 8

 

Next you will configure wiegand on both devices.As well as the 12v power for the power to the strike/lock 

A092:

Wiegand Setup

Login> Device> Wiegand> Check mark Wiegand Open relay A or B> Wiegand Transfer mode must be INPUT and submit

12V Setup

Login>Access Control> Relay> 12V Power Output> Dropdown to Always and submit 

Note: On the Device sending the pin (r27 in this example) we must also access the wiegand settings convert the wigend to a pin and change the Transfer mode to Output.

R27 Wiegand: 

    • Related Articles

    • Akuvox Local || EC33 Wiegand Settings

      EC33 Wiegand Settings EC33 can be connected to third-party devices such as card readers via Weigand. You set the Wiegand setting based on the technical specification of the third-party device for the integration. Navigation Path: Setting > Wiegand. ...

    • General || SSL Certificate Local installation

      SSL Certificate Local installation In certain installations, it may be required to use the HTTPS protocol which safely encrypts data between the web browser and the IP camera (or the recorder). Nowadays, almost all security IP cameras and NVRs ...

    • Akuvox Cloud || Akuvox RF card setup

      There are a few ways to assign RF cards to cloud users. It is important to understand that there are 2 types of users within an Akuvox system. There is local which is created on the device itself, and cloud which is created on the cloud. This will ...

    • Akuvox General || Akuvox pre-requisite and requirements

      1. An Akuvox Installer Account Web Portal Login (If planning to use cloud services to setup and manage) a. Installer accounts are created for all new Akuvox customers. This account is used to create, setup and manage each project/ property, Akuvox ...

    • Akuvox Local || RTSP configuration

      All Akuvox Doorphones that have cameras support RTSP. Akuvox RTSP string - rtsp://X.X.X.X/live/ch00_0 Setting up RTSP on Android based doorphones Step 1: Log into the device using the local IP. Default is admin / admin. Step 2: Navigate to Intercom ...