Emerald IPC
Emerald IPC || How to enable Panoramic PTZ Linkage for EM-TPTZP44100-X25-LHAD
How to enable Panoramic PTZ Linkage for EM-TPTZP44100-X25-LHAD Enter setup menu Enter Intelligent menu Under Smart-> (1)Enable Panoramic Linkage and select the (2)Configuration button Ensure (1)Panoramic Linkage is enabled, and select (2)Continuous ...
Emerald IPC || IP Camera Hard Reset
This guide will use EM-IPCP8D3-F28-LH-AI as an example of a IPC that has a physical reset button. IPCs with a reset button will be listed at the bottom as well as a video demonstration. Step 1. Verify that the device is powered up. One of the ways ...
Emerald IPC || Change IPC from Line to Mic
Change IPC from line to mic * Note camera needs to have 2-way functionality. You may also use the Access button while on the same network as the recorder. If not, you must use the IP address of the IP camera. 1. Type IP address for camera on URL. 2. ...
Emerald IPC || How to configure Snapshot
Log onto the web interface To configure a snapshot, under setup go to events on the left hand side and the camera image should come up. Detection mode is set to area on this camera so that means whatever comes into that specific area the camera will ...
Emerald IPC || How to view snapshots from IP Camera
Log into the web interface Under the photo option on the top of the page it will take you to where the snapshots are stored on the camera. In this screenshot the camera was set to take snapshots whenever motion is detected. Navigate to the proper ...
Emerald IPC || How to configure IP Camera to record to SD-Card
Log onto the web interface for the camera Under setup go to storage on the left-hand side of the page Storage medium should be the SD card you've placed into the camera and make sure to format it to be able to use it. Allocate capacity is used for ...
Emerald IPC || How to playback video from IP Camera that has SD-Card Installed
Log into the camera from the web interface Go to the playback option and from there you will have access to the recordings right on the camera. On the right side you see a calendar, that is for you to filter out certain dates you would like to view ...
Emerald IPC || How to locate IP Camera on LAN via ENS Station
Open ENS Station and navigate to device management Here you can see the IP cameras by IP address. You can locate your specific camera by ip address, model number or Serial number. The cameras you see already are on the network so you can quickly add ...
Emerald IPC || How to Configure Image Settings of IP Camera
After logging in, under setup on the left hand side, there should be a video tab, and go to video once more to access video settings. In the next few screenshots you will see the different settings 1.1. Here are the image enhancement settings, if the ...
Emerald IPC || How to reset IP camera
1. Log onto the remote web interface 2. Under the setup menu, on the left hand side go all the way down to the System tab 3. Under the system tab, go to the maintenance option and you will see config management, the default option factory defaults ...
Emerald IPC || How to Set IP Camera to Static
1. After logging in go under setup, go to network settings on the left hand side, then click on network once more 2. The option where it says obtain IP address you're going to want to click on that option and a drop-down menu appears, from there you ...
Emerald IPC || How to Set Date and Time on an IP Camera
1. After you have logged into the remote web interface for the camera, on the banner options go to setup on the left-hand side there should be date and time options available for configurations. 2. Expanding further you can see 2 options for time, ...
Emerald IPC || How to locate device on LAN via ENS tool
How to locate IP Camera on LAN via ENS Station 1.Connect camera to POE switch 2.Open ENSTools and camera should take a few moments to pop up (Highlighted below) 3. Under the configuration tab click on the E symbol corresponding to the camera and log ...